• Multirope load weighing device for rope lifts
  • Rope diameter: from 6 to 16 mm
  • Only 8 cm height on the rope
  • Suitable for wire or plastic  ropes
  • Good price/performance ratio
  • Extremely compact


The Multirope MRL100 load weighing device can be used to measure and control the load in the cabin through the tensioning of the ropes.

It can be easily installed in new lifts and used for modernization, being fast to install, reliable over time and with a good price.

With a height on the rope of 8 cm only, the MRL sensors allow the optimization of the vertical spaces of the plant system that is typical of modern lifts (Machine Room Less), where every inch of space is important for installing the plant system in accordance with modern design practices.
The MRL100 sensor should be applied to all ropes of the plant system – disposing of a space for 72 mm wide ropes – in a position suitable to detect the load present in the cabin and has dimensions that make it possible to install it on the latest ropes clad in plastic material or flat ropes. The load measurement is independent from the roping of the plant roping.

The flexibility of transducer installation arises from design choices aimed at creating a simple, secure installation and a product that can be easily configured to suit the diameter of the ropes on which it will be installed. In order to adapt the MRL sensor to the diameter of the rope involved, it is necessary to use two connecting screws – between sensor and central deflection rod – corresponding to the diameter of the rope involved. There are several types of connection screws, each of them covers several ropes diameters, so as to be able to simplify product management.

In the standard measurement configuration, the MRL sensor detects (P + Q) loads of up to a maximum of 4,000 Kg. Customized configurations of the product are possible in order to suit specific application needs.

The MRL sensor is normally supplied with pre-wired cable with RJ connector in order to facilitate and speed up the sensor connection to the 699Plus digital control unit. 

The MRL series transducers are products that are designed and manufactured in Italy, are easily configurable and adaptable to the various plant system requirements that can be requested to meet the most demanding market requirements.


The Multirope load weighing system is applied on rope lifts and elevators, Machine Roomless Elevators (MRL), goods lift freight elevators and domuns lifts. It is suitable for installation on new lifts and also on the modernization of old installations. MRL transducers can be used even on flat ropes

The MRL series sensors can be used not only on lifts, but wherever the measurement of the tensioning load on ropes is required, such as for example the lifting of equipment in the theater settings, for industrial lifting applications, naval applications, cable cars, etc.

MRL caricato

  • MRL Transducer highness: 80 mm.
  • Maximum load measure: 4000 kg
  • Rope diameters: 6.5mm, works with 3, 4 or 6 ropes (other diameters or rope numbers upon request)
  • Overall maximum rope spacing: 72 mm.

When paired with the optional 699 electronic device it has:

  • Alarm levels: 2pcs. with NC and NO, third alarm with relay for booking and distress signal handling.
  • Power supply: 12 and 24Vdc/ac.
  • Buzzer: for sound signalling.
  • Optical indicator: for signalling the load status in the cabin.
  • Relays block when cabin is moving.


  • Outputs: 0-5V, CANOpen, RS485 Modbus.
  • Accelerometer: for measuring the acceleration and tilt of cabin.
  • Easy adapting of the MRL100 transducer to different rope numbers or diameters

MRL100 transducer is installed on the ropes close to their fixing points on the cabin roof and measures the load by measuring the tension of all the ropes at the same time.Mod. 699 electronics can be connected to mod. MRL100 transducer and controls the cabin load by means of its alarm levels.Transducer mod. MRL100:Easy and quick to install: only two screws are to be fixed- Miniaturized: its 80mm overall highness allow its installation even when cabin is at the top of hoistway close to the pulley.- Warehousing cost reduction: it is not necessary to buy, and keep on stock, as many MRL as all the possible rope diameters because customer can easily modify in the field heir rope diameter setting (option).- MRL100 can be installed even with widely spaced ropes or with many ropes: MRL allows to accept ropes with a 72 mm max. overall spacing width- Belts: MRL can be installed on elevators that use belts instead of ropes.- Output: 2mV/V, non linearity: ±0,2%FS, strain gauge bridge impedance: 1KOhm, connection cable 2m long.- MRL100 transducer can be separately sold without 699 electronics for direct connection to the customer’s electronics.- Innovative and patented. Mod. 699 digital electronics:With microprocessor, with high brightness 4 digits LEDs display, it feeds power to connected MRL transducer, it shows the load value in the cabin in engineering units (Lbr, Kg, daN etc.) and it controls the load by means of alarm levels with relays outputs.- Easy to install: quick calibration menu is quick to use.- Easy to service: error codes help during installation and after sale service.- Reliability: compensation of thermal drifts and mechanical settlings.- Alarm levels: two NC/NO relays outputs (full load and overload) are auto-calibrating with relationship to full load.- Power supply: 12 or 24Vdc/ac (in case of black out calibrations are maintained in memory).

To make an order or to find the best solutions for your requirements, please don’t hesitate to contact us at the following email:[email protected]