Contact us: +39 02 89 101 42 – Contacts
0,00 €
Column load cells Serie Ap8000, for compression, find main applications in weighing systems, platforms, reservoirs, bunkers, hoppers and for general purpose.
These load cells have a high accuracy, outstanding ruggedness, easiness of installation and a convenient price.
The body of the load cell is in high strength steel and strain gauges and internal electrical circuits are sealed and stuffed by water-repellent high-insulating silicon filler for outdoor applications.
Different measuring configurations are available. Among them a version with a 16 strain gauges is available. They are well distributed along the circumference to improve the insensitivity to transverse components of the applied force, to assure an excellent linearity, higher electrical excitation and signal output. This last feature is important because amplifier gain , electrical noise and theermal drift are reduced and digital readout can be extended to more digits to improve the measuring resolution.
Transducers have an internal calibration circuit to allow an easy calibration of the weighing system and to verify the functioning of the unit. Each load cell is supplied with an individual calibration certificate.
Load cells Series AP8000 are available with two different possibilities of electrical connections: connector or shielded cable. The transducer can have a built-in electronics to gain a a voltage, current or digital amplifed signal.
Different versions of the transducer are available:
Fullscale | |
---|---|
Sensitivity | 1 mV/V FS |
Creep Error | <±0,15% FS (during 4 hours test at FS) |
Maximum error (non-linearity + hysteresis + temperature effect on sensitivity) | <±0.1% FS |
Temperature effect error on zero output | within 5°K <±0,1% FS |
Measuring ranges | 0 ± 25 Ton |
Sensitivity | 1 mV/V FS typical |
Dead load | ≤50 intervals (ECC-335) |
Maximum error (non-linearity + hysteresis + temperature effect on sensitivity) | < ± 0,2% FS |
Repeatabiity error | ≤ 0,1% FS |
Temperature effect error on zero output | within 5°K ± 0,1% FS |
Creep error | < ± 0,15% FS, during 4 hours test at FS |
Zero output return error | ≤± 0,07% FS after 30 min at FS |
Zero unbalance | ≤± 2% FS |
Bridge impedance | output: 1400 Ohmsinput: 1500 Ohms, nominal |
Insulation resistance | > 5000 Mohms |
Excitation | recommended: 10 Vdc/acmaximum: 18 Vdc/ac |
Safe load limit | 50% over FS (with load on the weighing axis) |
Ultimate Ioad limit | about 2 times the FS (with load on the weighing axis) |
Electrical connection | by cableby connector (on request) |
Color code (Numbers for connector) | Excitation: + red (+1) – black (-4)Output: + green (+2) – white (-3) |
Temperature limits | Compensated: -10°C + 40°C (OIML Rec. N°60)Operating: -15°C ± 75°C |
Rh | < 95% |
Environment protection | IP65 |
MODELLO | CAMPO DI MISURA | DIMENSIONI (mm) | |||||||||
Ton | A | D | E | F | G | H | J | K | M | N | |
AP8005 | 0 ± 5 | 35 | 12 | 15 | 50 | 83,2 | M10 | 33 | R25 | ||
AP8010Flat | 0 ± 10 | 35 | 12 | 15 | 50 | 38,5 | 83 | M10 | 7 | 33 | |
AP8010Round | 0 ± 10 | 35 | 12 | 15 | 50 | 38,5 | 83 | M10 | 3 | 33 | R25 |
AP8025Flat | 0 ± 25 | 35 | 12 | 15 | 70 | 48,5 | 98 | M10 | 12 | 53 | |
AP8025Round | 0 ± 25 | 35 | 12 | 15 | 70 | 48,5 | 98 | M10 | 5 | 53 | R40 |
AP8050 | 0 ± 50 | 58 | 20 | 20 | 77 | 50 | 130 | M18x2.5 | 10 | 50 | R100 |
AP8100 | 0 ± 100 | 100 | 15 | 20 | 116 | 80 | 190 | M18 | 15 | 80 | 110 |
To make an order or to find the best solutions for your requirements, please don’t hesitate to contact us at the following email:[email protected]